Back to home
Ametek
 

EN 61000-6-4

  • Product

    Description

     
  • BHA 9118

    BHA 9118

    The BHA 9118 is a linearly polarised broadband antenna which is ideal for many applications particularly EMC/RF measurements.

  • CBL 6111

    CBL 6111

    The CBL 6111 is a high performance ultra wideband BiLog® antenna for emission and immunity EMC testing.

  • CBL 6112

    CBL 6112

    The CBL 6112 operates over the unprecedented, wide range 30 MHz to 2 GHz.

  • CBL 6141

    CBL 6141

    For RF EMC emission and immunity testing in compact anechoic chambers.

  • CBL 6143

    CBL 6143

    The CBL 6143 has a unique matching network which will allow powers of up to 300 watts CW to be transmitted, making it suitable for most immunity measurements requiring fields of 10 V/m, or even greater.

  • CBL 6144

    CBL 6144

    The CBL 6144 gives an incredible antenna factor of only 3 dB at 26 MHz together with a useable VSWR making the CBL 6144 able to deliver 10 V/m with 80% AM modulation using an amplifier power of less than 500 W (chamber dependent) at 26 MHz.

  • CDN S Series

    CDN S Series

    CDN S Series

  • CMAD 20B

    CMAD 20B

    Reproducible emissions measurements require a defined line termination for the frequency range where connected lines provide a significant influence on the emissions.

  • Compliance 5 Emission

    Compliance 5 Emission

    Compliance 5 is sophisticated EMC laboratory control software designed to make RF Emission testing fast, efficient, compliant, accurate and simple.

  • CFL 9206

    CFL 9206

    The CFL 9206 assists in preventing damage to input circuits of measuring equipment from high level transients often encountered during conducted emission testing.

  • CSP 9160

    CSP 9160

    The CSP 9160 is a broadband RF current sensor probe as defined in CISPR 16-1-2. Beside the compliance measurements of asymmetrical disturbance currents as e.g. required in CISPR 16-2-1 and CISPR 22, the probe can be used in a number of diagnostic applications to measure superimposed RF currents flowing in conductors, or cable harnesses.

  • CVP 2200A

    CVP 2200A

    The Capacitive Voltage Probe (CVP) is designed for measuring asymmetrical disturbances on cables with capacitive coupling principle.

  • DPA 3000

    DPA 3000

    The dipole antenna DPA 3000 operates as a field strength measuring antenna in the frequency range 800 to 2800 (3000*) MHz.

  • DPA 4000

    DPA 4000

    The dipole antenna DPA 4000A operates as a field strength measuring antenna in the frequency range 200 (30*) to 1000 MHz.

  • GTEM 250

    GTEM 250

    The GTEM 250 has a maximum septum height of 250 mm and is suitable for emissions and immunity testing.

  • GTEM 500

    GTEM 500

    The GTEM 500 has a maximum septum height of 500 mm and is suitable for emissions and immunity testing.

  • GTEM 750

    GTEM 750

    The GTEM 750 has a maximum septum height of 750 mm and is suitable for emissions and immunity testing.

  • GTEM 1000

    GTEM 1000

    The GTEM 1000 has a maximum septum height of 1000 mm and is suitable for emissions and immunity testing.

  • GTEM 1250

    GTEM 1250

    The GTEM 1250 has a maximum septum height of 1250 mm and is suitable for emissions and immunity testing.

  • GTEM 1500

    GTEM 1500

    The GTEM 1500 has a maximum septum height of 1500 mm and is suitable for emissions and immunity testing.

  • GTEM 1750

    GTEM 1750

    The GTEM 1750 has a maximum septum height of 1750 mm and is suitable for emissions and immunity testing.

  • GTEM 2000

    GTEM 2000

    The GTEM 2000 has a maximum septum height of 2000 mm and is suitable for emissions and immunity testing.

  • HLA 6121

    HLA 6121

    The active loop antenna HLA 6121 is designed for operation in the frequency range 9 kHz to 30 MHz. It is ideally suited for magnetic field measurements as required by several standards (e.g. CISPR 11, CISPR 16-1-4, CISPR 16-2-3, FCC 18 and others).

  • ISN S Series

    ISN S Series

    ISN S series is designed for measurements on coaxial telecommunication lines.

  • ISN T2

    ISN T2

    The ISN T2 is designed for measurements on one unscreened balanced pair for cable cat. 3 and cat. 5.

  • ISN T4

    ISN T4

    The ISN T4 is designed for measurements on one or two unscreened balanced pairs for cable cat. 3 and cat. 5.

  • ISN T8-Cat6

    ISN T8-Cat6

    The ISN T8-Cat6 is designed for measurements on up to four unscreened single balanced pairs with cable category cat. 6.

  • ISN T8

    ISN T8

    The ISN T8 is designed for measurements on up to four unscreened balanced pairs for cable cat. 3 and cat. 5.

  • KSQ 1000

    KSQ 1000

    The KSQ 1000 is a special version of reference radiation source for the frequency range 30 MHz to 1 GHz.

  • LNA 6000

    LNA 6000

    The LNA 6000 is a low noise amplifier with 12.5 dB of gain covering the nominal frequency range 1 MHz to 3 GHz and can be used in the range from 200 kHz to 4 GHz.

  • LNA 6900

    LNA 6900

    The LNA 6900 is a low noise amplifier with 25 dB of gain covering the nominal frequency range 9 kHz to 2 GHz and can be used up to 4 GHz.

  • LNA 6901

    LNA 6901

    The LNA 6901 is a low noise amplifier with typ. 28 dB of gain covering the nominal frequency range 9 kHz to 1 GHz and can be used up to 2 GHz.

  • NNB 51

    NNB 51

    Line impedance stabilization network (LISN) such as the NNB 51 are used to measure distortion signals on the mains cord of an electrical equipment under test (EUT).

  • RSG 1000

    RSG 1000

    The RSG 1000 is a reference spectrum generator for the frequency range from 1 MHz to 1 GHz.

  • RSG 3000

    RSG 3000

    The RSG 3000 is a reference spectrum generator for the frequency range from 1 MHz to 6 GHz.

  • UPA 6108

    UPA 6108

    The UPA 6108 and UPA 6109, suitable for CISPR/IEC/EN, FCC, MIL-STD testing, are small yet rugged antennas covering the frequency range 200 MHz - 1 GHz (UPA 6109), and 300 MHz - 1 GHz (UPA 6108).

  • UPA 6109

    UPA 6109

    The UPA 6108 and UPA 6109, suitable for CISPR/IEC/EN, FCC, MIL-STD testing, are small yet rugged antennas covering the frequency range 200 MHz - 1 GHz (UPA 6109), and 300 MHz - 1 GHz (UPA 6108).

  • UPA 6192

    UPA 6192

    The UPA 6192 antenna is hybrid antenna with the characteristics similar to a broad band dipole in the range 30 - 200 MHz and a log periodic antenna in the range 200-2000 MHz.

  • VBA 6106

    VBA 6106

    The VBA 6106A is suitable for CISPR/EN, FCC and MIL-STD testing across the frequency range 30-300 MHz.

  • VSQ 1000

    VSQ 1000

    The VSQ 1000 is a radiation source for the frequency range from 30 MHz to 1 GHz.

  • VSQ 3000

    VSQ 3000

    The VSQ 3000 (VSQ 3002) is a radiation source for the frequency range from 800 MHz (30 MHz) to 3 GHz.

 
 
 

Imprint

AMETEK CTS GmbH
Sternenhofstr. 15
4153 Reinach, Switzerland
Tel.+ 41 61 204 41 00
marketing.cts@ametek.com

Managing Directors:
Brian Huntsman
Astrid Wälchli Schreiber
VAT-ID: CHE-179.452.414
Register of companies: CH-280.4.015.069-3


 
 
By continuing to use the site, you agree to our Privacy and Cookie Policy.